vintage_net

# VintageNet Cookbook
Not sure what to pass to `vintage_net`? Take a look below for example
configurations.
## Compile-time vs. run-time
The examples below all show the options to pass. Where you copy those depends on
whether you want the configuration to be a built-in default (i.e., compile-time)
or whether you want to change it at run-time.
For compile-time, add something like the following to your `config.exs`:
```elixir
config :vintage_net,
  config: [
    {"eth0", %{type: VintageNetEthernet, ipv4: %{method: :dhcp}}},
  ]
```
But replace `"eth0"` with the interface and the map with the desired
configuration from below.
For run-time, call
[`VintageNet.configure`](https://hexdocs.pm/vintage_net/VintageNet.html#configure/3)
like this:
```elixir
VintageNet.configure("eth0", %{type: VintageNetEthernet, ipv4: %{method: :dhcp}}})
```
To see the current configuration at an IEx prompt, type:
```elixir
iex> VintageNet.info
```
## Network interface names
In order to configure a network interface, you will need to know its name.
`vintage_net` passes names through from Nerves or embedded Linux depending on
where it's being run. The following names are common:
* `"eth0"` - The first wired Ethernet interface
* `"wlan0"` - The first WiFi interface
* `"usb0"` - The first virtual Ethernet interface over a USB cable
The operating system assigns network interface names as it discovers them. If
you're running on a device with multiple of the same type of interface, the
device names may be renamed to make them deterministic. An example is `"enp6s0"`
where the `p6` and `s0` indicate where the adapter and Ethernet connector
location. Running `ifconfig` on Linux and Nerves can help find these if you are
unsure.
## Wired Ethernet
To use, make sure that you're either using
[`nerves_pack`](https://hex.pm/packages/nerves_pack) or have
`:vintage_net_ethernet` in your deps:
```elixir
  {:vintage_net_ethernet, "~> 0.7"}
```
### Wired Ethernet with DHCP
This is regular wired Ethernet - nothing fancy:
```elixir
%{type: VintageNetEthernet, ipv4: %{method: :dhcp}}}
```
### Wired Ethernet with a static IP
Update the parameters below as appropriate:
```elixir
%{
  type: VintageNetEthernet,
  ipv4: %{
    method: :static,
    address: "192.168.9.232",
    prefix_length: 24,
    gateway: "192.168.9.1",
    name_servers: ["1.1.1.1"]
  }
}
```
See
[`VintageNet.IP.IPv4Config`](https://hexdocs.pm/vintage_net/VintageNet.IP.IPv4Config.html)
for other options. If you're interfacing with other Erlang and Elixir libraries,
you may find passing IP tuples more convenient than passing strings. That works
too.
## WiFi
To use, make sure that you're either using
[`nerves_pack`](https://hex.pm/packages/nerves_pack) or have
`:vintage_net_wifi` in your deps:
```elixir
  {:vintage_net_wifi, "~> 0.7"}
```
### Normal password-protected WiFi (WPA2 PSK)
Most password-protected home networks use WPA2 authentication and pre-shared
keys.
```elixir
%{
  type: VintageNetWiFi,
  vintage_net_wifi: %{
    networks: [
      %{
        key_mgmt: :wpa_psk,
        ssid: "my_network_ssid",
        psk: "a_passphrase_or_psk"
      }
    ]
  },
  ipv4: %{method: :dhcp},
}
```
### Enterprise WiFi (PEAPv0/EAP-MSCHAPV2)
Protected EAP (PEAP) is a common authentication protocol for enterprise WiFi networks.
```elixir
%{
  type: VintageNetWiFi,
  vintage_net_wifi: %{
    networks: [
      %{
        key_mgmt: :wpa_eap,
        ssid: "my_network_ssid",
        identity: "username",
        password: "password",
        eap: "PEAP",
        phase2: "auth=MSCHAPV2"
      }
    ]
  },
  ipv4: %{method: :dhcp}
}
```
### Enterprise WiFi (EAP-TLS)
TBD
### Access point WiFi
Some WiFi modules can be run in access point mode. This makes it possible to
create configuration wizards and captive portals. Configuration of this is more
involved. Here is a basic configuration:
```elixir
%{
  type: VintageNetWiFi,
  vintage_net_wifi: %{
    networks: [
      %{
        mode: :ap,
        ssid: "test ssid",
        key_mgmt: :none
      }
    ]
  },
  ipv4: %{
    method: :static,
    address: "192.168.24.1",
    netmask: "255.255.255.0"
  },
  dhcpd: %{
    start: "192.168.24.2",
    end: "192.168.24.10"
  }
}
```
See the
[vintage_net_wizard](https://github.com/nerves-networking/vintage_net_wizard)
for an example of a project that uses AP mode and a web server for WiFi
configuration.
## Network interaction
### Share WAN with other networks
For sharing your WANs connection (e.g. internet access) with other networks `iptables` must be installed. Currently this means building a [custom nerves system](https://hexdocs.pm/nerves/customizing-systems.html). Once this is done the following commands need to be called on each boot:
```elixir
wan = "eth0"
cmd "sysctl -w net.ipv4.ip_forward=1"
cmd "iptables -t nat -A POSTROUTING -o #{wan} -j MASQUERADE"
# Only needed if the connection is blocked otherwise (like a default policy of DROP)
cmd "iptables -A INPUT -i #{wan} -m state --state RELATED,ESTABLISHED -j ACCEPT"
```