Packages
nerves_system_rpi
1.3.0
2.1.0
2.0.4
2.0.3
2.0.2
2.0.1
2.0.0
2.0.0-rc.3
2.0.0-rc.2
2.0.0-rc.1
retired
2.0.0-rc.0
retired
1.33.1
1.33.0
1.32.0
1.31.4
1.31.3
1.31.2
1.31.1
1.31.0
1.30.1
1.30.0
1.29.1
1.29.0
1.28.1
1.28.0
1.27.1
1.27.0
1.26.0
1.25.1
1.25.0
1.24.1
1.24.0
1.23.2
1.23.1
1.23.0
1.22.2
1.22.1
1.22.0
1.21.2
1.21.1
1.21.0
1.20.2
1.20.1
1.20.0
1.19.0
1.18.4
1.18.3
1.18.2
1.18.1
1.18.0
1.17.3
1.17.2
1.17.1
1.17.0
1.16.2
1.16.1
1.16.0
1.15.1
1.15.0
1.14.1
1.14.0
1.13.3
1.13.2
1.13.1
retired
1.13.0
1.12.2
1.12.1
1.12.0
1.11.2
1.11.1
1.11.0
1.10.2
1.10.1
1.10.0
1.9.2
1.9.1
1.9.0
1.8.2
1.8.1
1.8.0
1.7.2
1.7.1
1.7.0
1.6.3
1.6.2
1.6.1
1.6.0
1.5.1
1.5.0
1.4.0
1.3.0
1.2.1
1.2.0
1.1.1
1.1.0
1.0.0
1.0.0-rc.0
0.20.0
0.18.0
0.17.1
0.17.0
0.16.1
0.16.0
0.15.0
0.14.0
0.13.0
0.12.0
0.11.0
0.10.0
0.9.1
0.9.0
0.7.0
0.6.1
0.6.0
0.5.2
0.5.1
0.5.0
0.4.1
Nerves System - Raspberry Pi A+ / B+ / B
Current section
Files
Jump to
Current section
Files
nerves_system_rpi
config.txt
config.txt
# Default Nerves RPi config.txt
#
# It's possible to override this file by using a custom fwup.conf
# configuration to pull in a replacement.
#
# Useful links:
# https://www.raspberrypi.org/documentation/configuration/config-txt/README.md
# https://github.com/raspberrypi/documentation/blob/master/configuration/device-tree.md
kernel=zImage
# This, along with the Raspberry Pi "x" firmware is need for the camera
# to work. The Raspberry Pi "x" firmware is selected via the Buildroot
# configuration. See Target packages->Hardware handling->Firmware.
gpu_mem=192
# Enable I2C and SPI
dtparam=i2c_arm=on,spi=on
# Comment this in or modify to enable OneWire
# NOTE: check that the overlay that you specify is in the boot partition or
# this won't work.
#dtoverlay=w1-gpio-pullup,gpiopin=4
# Enable the UART via GPIOs 14 and 15 (ttyAMA0) on the RPi0 W.
# See https://www.raspberrypi.org/documentation/configuration/uart.md.
enable_uart=1
dtoverlay=pi3-miniuart-bt