Packages

nerves_system_rpi

1.22.2
2.1.0 2.0.4 2.0.3 2.0.2 2.0.1 2.0.0 2.0.0-rc.3 2.0.0-rc.2 2.0.0-rc.1 retired 2.0.0-rc.0 retired 1.33.1 1.33.0 1.32.0 1.31.4 1.31.3 1.31.2 1.31.1 1.31.0 1.30.1 1.30.0 1.29.1 1.29.0 1.28.1 1.28.0 1.27.1 1.27.0 1.26.0 1.25.1 1.25.0 1.24.1 1.24.0 1.23.2 1.23.1 1.23.0 1.22.2 1.22.1 1.22.0 1.21.2 1.21.1 1.21.0 1.20.2 1.20.1 1.20.0 1.19.0 1.18.4 1.18.3 1.18.2 1.18.1 1.18.0 1.17.3 1.17.2 1.17.1 1.17.0 1.16.2 1.16.1 1.16.0 1.15.1 1.15.0 1.14.1 1.14.0 1.13.3 1.13.2 1.13.1 retired 1.13.0 1.12.2 1.12.1 1.12.0 1.11.2 1.11.1 1.11.0 1.10.2 1.10.1 1.10.0 1.9.2 1.9.1 1.9.0 1.8.2 1.8.1 1.8.0 1.7.2 1.7.1 1.7.0 1.6.3 1.6.2 1.6.1 1.6.0 1.5.1 1.5.0 1.4.0 1.3.0 1.2.1 1.2.0 1.1.1 1.1.0 1.0.0 1.0.0-rc.0 0.20.0 0.18.0 0.17.1 0.17.0 0.16.1 0.16.0 0.15.0 0.14.0 0.13.0 0.12.0 0.11.0 0.10.0 0.9.1 0.9.0 0.7.0 0.6.1 0.6.0 0.5.2 0.5.1 0.5.0 0.4.1

Nerves System - Raspberry Pi A+ / B+ / B

HexDocs

Current section

Files

Jump to
Readme
117 Versions
3 Dependencies
Dependants
Files
Activity
nerves_system_rpi cmdline.txt
Raw

cmdline.txt 

# NOTES:

# 1. Kernel messages are output to HDMI and the UART pins by default.

# 2. serial0 is magically replaced with ttyAMA0 or ttyS0 depending on the

#    serial port configuration in config.txt.

# 3. To remove the kernel messages going to HDMI, remove

#    "console=tty1 fbcon=scrollback:1024k consoleblank=0"

# 4. If you're experimenting with kernel commandline parameters, it's easist

#    to modify this file on the MicroSD card via your development computer. To

#    make changes permanent, you'll need to override the fwup.conf.

# 5. See https://www.raspberrypi.org/documentation/configuration/cmdline-txt.md

root=/dev/mmcblk0p2 rootwait console=serial0,115200 console=tty1 fbcon=scrollback:1024k consoleblank=0